You’ve just unpacked your new hoverboard and are ready to take it for a spin. You hop on, push off with your foot, and—whoa!—you immediately start wobbling uncontrollably.
Don’t worry, this is totally normal. How to configure hoverboard controls in fact, every new hoverboard goes through a slight calibration process in order to adjust to the weight and movement of its rider. Luckily, it’s a quick and easy process that anyone can do.
In this article, we’ll show you how to calibrate your hoverboard quickly and easily.
Understanding Hoverboard Calibration
When you get a new hoverboard, the first thing you’ll want to do is calibrate it. This ensures that the board is operating at peak performance and that you stay safe while riding.
There are a few things you need to understand about hoverboard calibration before getting started:
- The calibration process adjusts the settings on your hoverboard to match your weight and height. This is important, as it ensures that the board is able to safely carry you while you’re riding.
- You’ll need to calibrate your hoverboard each time you change its battery. This keeps the board’s settings in sync with your weight and height.
- There are two ways to calibrate a hoverboard: manually and automatically. We’ll cover both methods below.
Setting Up the Hoverboard Balance
Now that your hoverboard is in your hands, it’s time to set it up. This is a very important step that ensures the safety of both you and your hoverboard.
There are two ways to adjust the balance on your hoverboard: by using the footpads or by using the remote control. We’ll go over both methods below.
Syncing the Hoverboard Sensors
Now it’s time to calibrate your hoverboard sensors. This will ensure that your hoverboard is working at its best and that you’re riding safely.
To sync the sensors, place your hoverboard on a level surface and stand on it. Make sure that it’s in the power-on position and that the blue light is on. Hold down the power button for 10 seconds until the light turns off.
Release the button, and within a few seconds the blue light will turn back on. This means that your sensors have been synced.
Aligning the Hoverboard Wheels
The next step to calibrating your hoverboard is to align the wheels. To do this, gently lift the board and turn it so that the wheels are facing toward you. Then, look for a small locking screw on the inner side of each wheel. This screw should be tightened slightly to make sure that the wheel is securely fitted on the axle.
If the wheels aren’t properly aligned, this can cause your hoverboard to perform sluggishly and won’t be able to reach top speeds. Additionally, you can use a spirit level and ruler to measure if both wheels are level with one another and are of equal height from the ground.
Once you have checked these things, you’re ready to move on to inspecting any damages or debris in your hoverboard’s axle system.
Calibrating the Hoverboard Gyroscopes
Now for the tricky part – calibrating the gyroscopes in your hoverboard. This is a critical step that requires precision and patience, so take your time if you’re going to attempt it.
Before you begin, make sure that you have a flat surface with no bumps or stones that might interfere with the calibration. Once you are sure of your surface, turn on your hoverboard and place it in the balancing mode. This should be indicated by a spinning wheel on its dashboard.
Once the hoverboard is in balancing mode, press and hold both control buttons simultaneously until you hear two beeps. The LED display will then blink green and your board is now ready for calibration. To successfully calibrate the board’s gyroscopes, tilt it forward and then backward until you hear two more beeps. Make sure to keep your tilt angles consistent throughout this process – then it’s all finished!
Taking It for a Test Ride
Now that you’ve completed the necessary calibrations and adjustments, it’s time to take your hoverboard for a test ride. Make sure to take it slow and keep an eye on the LED lights. If one of the colors starts blinking, that could mean that the motor needs to be recalibrated.
When you’re out on your hoverboard, Best hoverboard for adult don’t forget to check the brakes. If they’re not working as they should, it’s time to adjust them again and make sure they’re properly calibrated. Another important thing is to do a quick spin test. This will ensure that all the connections between components are running smoothly and everything is in good working order before you set off on your ride.
Lastly, remember that checking your hoverboard’s calibration after every use is always a good practice for safety and performance reasons. Make sure all settings are where they should be, and you’ll always have an enjoyable ride and an optimum performance every time!
Conclusion
So, those are all the basics you need to know in order to adjust the settings on your hoverboard! As always, if you’re ever unsure about anything, it’s always best to consult your hoverboard’s user manual, or reach out to the hoverboard’s manufacturer for more help. With a little bit of practice, you’ll be able to have your hoverboard calibrated just the way you want it—and be riding around on it like a pro!
